Step inside an older Pasadena home and tap a wall with your knuckle. A hard, dense sound instead of a hollow one usually means plaster. Pasadena grew quickly in the early twentieth century, and the Craftsman bungalows and period revival houses of that era, including those in the Bungalow Heaven district, were commonly built with plaster over wood lath. That finish is durable and quiet, and it also behaves very differently from drywall when you pick up a roller.

How plaster walls are built

Traditional plaster is applied in layers. A rough scratch coat is pushed into narrow wood strips called lath, a brown coat builds the thickness, and a thin finish coat gives the surface its smoothness. Some homes use plaster over metal lath or masonry instead. The result is a wall that is often thicker, heavier and denser than modern gypsum board.

Because each layer was applied by hand, the surface carries slight waves and trowel marks. Those subtle variations are part of the character of a historic interior, and a good repaint respects them instead of fighting them.

Why the surface needs a different approach

Drywall has a paper face that accepts almost any paint. Plaster is mineral, porous and often alkaline when it is fresh, and over decades it has collected layers of old paint, wallpaper paste, smoke and cooking residue. Each of those layers affects adhesion.

  • Fresh or bare plaster can pull moisture out of water based paint too quickly, leaving a chalky film.
  • Old glossy enamel resists new coatings and will let them peel away.
  • Wallpaper adhesive that remains on the wall will bubble under latex paint.
  • Soot and grease prevent paint from bonding.

For these reasons, preparation takes more of the job than painting does.

Start with an honest inspection

Before choosing a product, walk the room and map what you see. Tap along the wall and listen for a change in sound. A dull, hollow tone in one area suggests that plaster has separated from the lath. Press gently on bulges to see whether they flex. Look at ceilings in particular, since gravity makes loose plaster there a safety issue, and call in a plasterer if sections sag.

Check the condition of the cracks too. Fine hairline cracks are common and expected. Long diagonal cracks above door frames, and cracks that reopen every season, can signal structural movement, which paint will not cure.

Lead safe practices in older homes

Many Pasadena houses predate 1978, when lead based paint was no longer used in homes. Layers of old paint on trim, and sometimes on plaster walls, may contain lead. The safest approach is to test suspect surfaces with a lead test kit or a lab, then follow lead safe practices when the surface will be disturbed.

Those practices include sealing off the work area, covering floors, misting surfaces before scraping, avoiding dry sanding and open flame, using a vacuum with a HEPA filter and keeping children and pregnant women away from the area. Professionals who disturb paint in pre-1978 housing are expected to be trained in them. A contractor who dismisses the question deserves a second look.

Cleaning, degreasing and removing what does not belong

Cleaning is the unglamorous first step. Dust the walls and ceiling, then wash with a mild detergent solution or a degreaser in kitchens, where cooking film settles. Rinse and allow the plaster to dry. Do not saturate it, since plaster can absorb water and take days to dry out.

Remove any loose wallpaper and its adhesive with a scraper and warm water, working gently so the finish coat of plaster is not gouged. Paint over leftover paste will lift, so patience here pays off later.

Repairing cracks and holes

Hairline cracks can be filled with a flexible patching compound or a lightweight spackle. Wider cracks need to be opened slightly with a utility knife, cleaned of dust and filled with a setting type joint compound or a patching plaster. Mesh or fiberglass tape across a larger crack reduces the chance of the crack returning.

Holes and missing chunks call for patching plaster, applied in thin layers and allowed to cure fully. Rushing a patch causes shrinkage lines that reappear through the finish. When the repair is dry, sand it level with the surrounding wall.

Be careful with sanding dust. Plaster dust is fine and travels, so wet sanding with a sponge or using a sander connected to a vacuum helps keep a house tidy.

Sanding, de-glossing and caulking

Once the wall is repaired, lightly scuff glossy surfaces with fine sandpaper or use a liquid deglosser so new paint can grip. Wipe down the dust afterward with a damp cloth. Seal gaps where plaster meets wood trim with a paintable caulk. A thin line of caulk along baseboards and casings hides the small gaps that form as an old house shifts, and it gives the finished room a crisp edge.

Priming: the step that decides the result

On plaster, primer is not optional. It equalizes porosity so the topcoat dries evenly, locks down stains and seals the alkaline surface.

  • A bare or freshly patched plaster wall usually needs a dedicated primer sealer, because patches absorb differently than the surrounding wall and will show as dull spots, called flashing, through a plain topcoat.
  • A wall with water stains, smoke marks or tannin bleed needs a stain blocking primer, sometimes oil based, so the marks do not return through the new finish.
  • A wall coated in sound old paint may only need a bonding primer to improve adhesion.

Test a small area before committing the whole room. Primer that peels from a test patch will peel across the room.

Choosing paint and sheen

Acrylic latex is the usual choice for interior plaster because it is flexible, low in odor and cleans up with water. Oil based enamel is still used on woodwork and in a few specialty situations, because it levels well and hardens thoroughly, but it yellows over time and releases strong fumes.

Sheen affects how forgiving a wall will be.

  • Flat or matte finishes hide the waves and trowel marks typical of old plaster, which is why many restorations favor them for walls and ceilings.
  • Eggshell and satin finishes offer more washability, useful in hallways and children's rooms, but they reveal imperfections under raking light from a window.
  • Semi-gloss belongs on trim, doors and cabinets where scrubbing is frequent.

If your Pasadena home gets strong afternoon light through large windows, test the finish on the wall at several times of day before you decide.

Applying the topcoat

Apply two coats, with proper drying time between them. Cut in the edges with a brush first, then roll the field using a roller cover with a nap suited to the surface. A slightly thicker nap handles a textured plaster finish better than a thin one, and a smoother finish takes a short nap.

Keep a wet edge, work from top to bottom and maintain steady lighting so you can see missed spots. Back-rolling immediately after a spray application is a common technique that works paint into the surface and avoids a sprayed look.

Ventilate the room, since plaster takes time to release moisture, and avoid painting in very humid conditions. Pasadena summers are dry, which helps drying times, but cool damp winter days can slow things down.

Mistakes that cause repeat work

  • Painting over wallpaper residue or soot without cleaning or sealing it.
  • Skipping primer on patched areas.
  • Using heavy, thick coats that crack as they dry.
  • Sanding dry in a house that may contain lead paint.
  • Covering active water stains without finding the leak.

When to bring in a professional

A small bedroom repaint can be a manageable weekend project. Whole house work, large ceiling repairs, stains from leaks and anything involving possible lead should go to someone with the right training. When you gather a bid, ask for a scope of work that lists the preparation steps, the primer, the paint line and the number of coats, so the proposal covers more than the visible color.

Respecting the character of old walls

Plaster is a feature, not a flaw. Done well, a repaint keeps the soft, hand made quality of the wall while giving it a clean, even finish, and it can last for many years. The effort goes into the quiet work of inspection, repair and priming, and the paint itself is the last and simplest step.